474 results found
-
Display time remaining during transition
Display the time remaining during the transition between columns.
I sometimes use very slow transition 150/300 sec, that would be very useful to know if the next column's opacity is already at 100%.
Thanks16 votes -
Audio delay offset
I have a video clip with mulitchannel audio output via a motu interface and I would like to be able to add an audio delay or offset in ms so that the audio will appear in sync with the video which is delayed by other external switchers/screen.
This could be done on a per media basis or as a global detting based on the audio routing device selected.
16 votes -
ISF transitions
The possibility to have an ISF effect switched from an input signal to a target signal as with a video mixer.
15 votes -
AMP over Ethernet for playback control from External
Add AMP or Odetics machine control for "next/previous/play/stop" control to allow for broadcast video switchers to trigger playback. This feature would make Millumin a powerhouse for touring and broadcast video playback.
15 votes -
Hours Field / milliseconds in frames - Timeline Setup
It would be great to have an hours field on the timeline setup page rather than having to convert hours to minutes to get a long timeline. Particularly when I am chasing timecode and need to start at 18 hours in.
Could the milliseconds field also be converted to frames?
14 votes -
TIME A JPEG
Attribute a time duration to a jpeg or a png to use the timer 's /BIGCLOCK benefits as sequence timer, without having to create a "dummy" audio file on another layer to time it!
14 votes -
sticky corners for screens in advanced layout
It'd be great when you create a screen in advanced layout to be able to drag corners or the whole screen while holding a modifier key to make it stick to the corners of the output or the corners of the other screens.
As an alternative, being able to adjust the X,Y position of each screen (top right or center) would work as well.
14 votes -
3D Object (UVW) Mapping
Semi-automatic 3D projection mapping (UVW), like Watchout, D3, Showlogic etc all have. Millumin has by far the best UI for quickly building shows. But unfortunately I find I have to use the above mentioned software for this key feature on most shows now. I wa hoping the "3D visualisation" in Mv2 was going to be this :-(
14 votes -
Total control for videos and cells (play, pause, time elapsed, total time)
Please total control for each cell
13 votes -
Automation curves in addition to keyframes
keyframes are fine but the curves are very helpful when automating and quickly see what is happening, because when you look only see diamonds and do not know which values have.
12 votes -
Show Control application
An independant application with :
- simple buttons to run the show
- overview of the columns
- notes
- preview of the output12 votes -
Audio plugins
Add audio plugins in effects section of layer or medias with audio content.
12 votes -
Timecode Clips should only start playing when timecode is received
When a clip is set to chase timecode it shouldn't be able to freerun when clicked. Instead if clicked it would show the first frame until timecode was received to trigger it.
12 votes -
Remember display fps and disable workspace at project reopen
I know it's just two clicks user side but it would be nice for millumin to remember within the .millumin file the states of "display fps" and "disable workspace".
12 votes -
delete warp points in mapping
Delete warp points in mapping. It would be great if you could warp a layer in the mapping and then go in and delete all your unused points from the middle, that way your layer wouldn't distort through all those unused center points.
12 votes -
Notes, update dynamic message via OSC
It would be useful to add the ability to dynamically update the messages in "notes" via OSC.
Like this mock-up :https://i.ibb.co/266b3RV/1.jpg
Adding simple graphics would be nice too.
https://i.ibb.co/YyJzvCk/2.jpg
Thanks
12 votes -
Possibility to change the height of the layers on Timeline mode
Possibility to change the height of the layers on Timeline mode for see more in layers view
11 votes -
Multiple canvas for timeline, available at the same time
Multiple canvas can help to display images over multiple videoprojector without being bored with the exceed of images on the edges (which is not the case if you "share" a canvas with several projector: a big image overlap on several projector). In many cases, timeline is useful to quickly edit and synchronize over the time what happen on several projectors (that are display through several canvases). Multiple canvases for the timeline is essential to use the canvases feature unless we have to go back to Millumin 1 process.
11 votes -
11 votes
-
Separate window for TimePanel
display Elapsed or remaining time in a separate window with options to display Info ( Color , Background, Font Size , position and even a Clock)
That could be very useful when you are running a show to have this window displayed on a separate monitor and share it with all the team working on a project )11 votes
- Don't see your idea?